输液瓶,infusion bottle
1)infusion bottle输液瓶
1.In order to understand the concentration changes of insulin injection in clinical transtusion and guide correct clinical operation,theinfusion bottle"s adsorption of the insulin injection was observed and studied.结果表明,不同材质和装有不同溶媒的输液瓶对胰岛素的吸附趋势类似,但塑料瓶对胰岛素的吸附量大于玻璃瓶,装有氯化钠的输液瓶大于葡萄糖输液瓶,100 g/L葡萄糖输液瓶大于50 g/L葡萄糖输液瓶。
英文短句/例句
1.OBSERVATION ON THE STERILE EFFECT OF STERILE ADHESIVE TAPE APPLIED TO INFUSION BOTTLES输液瓶口贴用于已开启液体瓶口消毒效果观察
2.Shaking infusion bottle regularly and standardizing intravenous infusion of insulin定时摇晃输液瓶 规范静脉输注胰岛素
3.Possibility analysis of contamination caused by withdraw of intravenous infusion bottle-needle静脉输液瓶端穿刺针后退操作污染可能性分析
4.Effects of Adsorption of Infusion Bottle on the Insulin Injection Concentration Changes in Clinical Transfusion输液瓶的吸附作用对胰岛素输注过程中浓度变化的影响
5.Methods Bacterial cultures were made on venipuncture needle, the puncture needle head of liquid bottle and the open site of rubber plug in intravenous transfusion.方法对输液过程中液体瓶塞开启处、输液管瓶端针头和静脉穿刺针分别进行细菌培养。
6.Development of Packing Material for Infusion and Process Design of Plastic Bottle and Soft Bag Workshop输液包材的发展及塑料瓶软袋车间的工艺设计
7.aluminium bottle [whether or not welded, of any capacity, for the transport or storage of compressed or liquefied gases]铝制的瓶[无论是否焊接,各种容量,用于运输或储存压缩或液化气体]
8.Influences of Temperature and pH Value of Fluids Contained in Glass Bottle upon Absorption of Insulin瓶装输液温度、pH值对胰岛素吸附作用的实验研究
9.cylinder ,aluminium, whethr or not welded, of any capacity, for the transport of storage of compressed or liquefied gases各种容量铝制气瓶,无论是否焊接,用于运输或储存压缩或液化气体
10.THE HANDLING CONDITION AND THE COUNTERMEASURE OF USED DISPOSABLE INFUSION BAG (BOTTLE) IN MEDICAL ESTABLISHMENTS OF SHANGHAI上海市医疗机构使用后一次性输液袋(瓶)处置状况与对策
11.Application on transfixion needle of disposable infusion apparatus for phacoemulsification输液器瓶盖穿刺针头在超声乳化白内障手术中的应用
12.supplying bottle供液瓶 -复印机的
13.Valves for liquid chlorine cylindersGB13439-1992液氯瓶阀
14.bottle of iron or steel[whether or not welded, of any capacity, of compressed or liquefied gases ]铁或钢制瓶[无论是否焊接,各种容量,用于运输或储存压缩或液化气体]
15.Liquid cylinders designed to dispense gaseous oxygen have valves equipped with standard Compressed Gas Association (CGA) outlets.设计用来输出气态氧的液体钢瓶上装有配有标准的压缩气体协会排气口的阀门。
16.Carbon dioxide is also stored and shipped as a liquid in cryogenic cylinders at reduced temperature and at a pressure of about 300 psig.二氧化碳还可以作为液体在压力减小到大约300 psig的低温钢瓶内储存和运输，
17.cylinder ,of iron or steel, whethr or not welded, of any capacity, for the transport or stroge of compressed or liquefied gases各种容量铁或钢制气瓶,无论是否焊接,用于运输或储存压缩或液化气体
18.aluminium bottle[ for the commercial conveyance or packing of goods (excl. compressed or liquefied gas), of a capacity not exceeding 300 L]铝制瓶[用于商业运输或包装货物（不包括压缩或液化气体）容量不超过300L]
相关短句/例句
infusion with double bottles双瓶输液
1.For the problem of mathematical modeling of givinginfusion with double bottles,4 cases are discussed,the equations of medicine liquid are obtained by both ways of differential equation and integral equation.湖北教育学院冯光庭等人著文讨论"双瓶输液中数理问题"。
3)medical transfusion bottle医用输液瓶
1.Structural characterization of speciality PP resin formedical transfusion bottle;聚丙烯医用输液瓶专用料结构表征
2.Industrial development of speciality PP formedical transfusion bottle;PP医用输液瓶专用树脂的工业开发
4)Glass infusion bottle玻璃输液瓶
5)bottle-type infusion device瓶式输液器
6)bottled infusion fluid瓶装大输液
1.METHODS:The hospital-preparedbottled infusion fluid was compared with soft parking fluid in respect to production costs,quality of preparation and clinical use.方法 :对医院瓶装大输液与软包装大输液从生产成本、制剂质量、临床应用情况等方面进行比较分析。
延伸阅读
L型（ 转弯型 ）600瓶/小时的洗瓶灌装压盖三合一设备介绍120瓶/小时的洗瓶灌装压盖三合一设备(4工位)480瓶/小时的洗瓶灌装压盖三合一设备(9工位)L型600瓶/小时的洗瓶灌装压盖三合一设备(7工位)1200瓶/小时的洗瓶灌装压盖三合一设备(9工位)10000瓶/小时的全自动小瓶洗瓶灌装设备6000瓶/小时的全自动小瓶洗瓶灌装设备L型（转弯型）600瓶/小时的洗瓶灌装压盖三合一设备介绍一、工艺流程进瓶-→洗涤液90秒冲洗除油物-→无菌水回水30秒冲洗-→消毒液150秒冲洗灭菌（两到消毒液冲洗）-→无菌水回水30秒冲洗-→无菌水（纯净水）30秒冲洗清瓶-→下瓶-→推瓶架正立瓶-→产品水灌注-→（理盖）挂盖-→压盖-→出瓶二、控制和制造上述过程均由PLC程序控制整个流程,精确定位自动完成，使用人力少、劳动强度低。全套设备采用进口不锈钢材料、镜面砂光板、精密氩弧焊接、变形小，焊纹美观；各传动件均为不绣钢结构,保证了机构在各种环境下正常运行；非金属件采用PP塑料等无毒高耐磨材料精心加工而成；主电机、输送带电机选用出口型系列产品,水泵选用德国格兰富系列产品，电气元件采用日本富士系列产品精装而成,整机性能稳定可靠。三、主要性能指标1．标准生产能力：600瓶/小时2.装机容量:11kW(不包括机体外设设备）3．供电要求：380V±5%50Hz4．压缩空气需求：0.3M3/Min7Kg/Cm25．整机外形尺寸：6650（长）×2040（宽）×2370（高）mm6．设备总重：1.8吨四、洗涤剂药物药物和消毒液的配置（一）建议使用二氧化氯强力洗涤消毒液。具体配置方法：原液(克)=用量(克)×使用浓度(ppm)/原液浓度(ppm)建议使用二氧化氯500-700ppm浓度的药液做洗涤、消毒液。在此浓度下，60秒时间清洗、消毒效果为99.99%：原液(克)=180000克用量×700ppm/20000ppm=6300克消毒液每小时更换一次。(二):使用说明1、主要特性和功能:A、本品在50-250mg/kg浓度下,作用5分钟,可100%杀灭细菌、真菌、霉菌和型肝炎病毒。B、本品能快速分解空气中的各种异味,具有除臭使空气清新的功能。C、以毒性、毒理测定证明:本品属实际无毒级,且无色,无剌激性。经本品消毒后的容器、设备、餐具可不再冲洗直接投入使用。D、本品原液保存期为一年半。2、用途:A、适用于食品、矿泉水、饮料、化妆品工业的设备、容器、管道及餐具的灭菌消毒。B、适用于家庭、医院、宾馆、公共场所及生产车间环境及空间的消毒灭菌。C、用于家庭房间、卫生间和宾馆空调房间等的除臭消毒,作空气清新剂使用。3、使用方法:使用时,必须加原液重量的1/20柠檬酸酸化,放置3-5分钟(液呈黄色),即用水稀释至所需的使用浓度,酸化时间超过七分钟以上时,稀释后的消毒液就会有气味,酸化时间越长,稀释后的消毒液的气味越大。使用浓度和作用时间 项 目对 象使 用 浓 度mg/kg作 用 时 间用法和用量餐具、水果、蔬菜分钟浸 泡
